DDR, DDR2, and DDR3 memories are classified according to the maximum speed at which they can work, as well as their timings. RAM Timings are numbers such as 3-4-4-8, 5-5-5-15, 7-7-7-21, or 9-9-9-24, the lower the better. In this tutorial, we will explain exactly what each one of these numbers mean.
DDR, DDR2, and DDR3 memories follow the DDRxxx/PCyyyy classification. By the way, if you are interested in knowing the difference between DDR, DDR2, and DDR3 memories, read our tutorial on this subject.
The first number, xxx, indicates the maximum clock speed that the memory chips support. For instance, DDR400 memories work at 400 MHz at the most, DDR2-800 can work up to 800 MHz, and DDR3-1333 can work up to 1,333 MHz. It is important to note that this is not the real clock speed of the memory. The real clock of the DDR, DDR2, and DDR3 memories is half of the labeled clock speed. Therefore DDR400 memories work at 200 MHz, DDR2-800 memories work at 400 MHz, and DDR3-1333 memories work at 666 MHz.
The second number indicates the maximum transfer rate that the memory reaches, in MB/s. DDR400 memories transfer data at 3,200 MB/s at the most, and hence they are labeled as PC3200. DDR2-800 memories transfer data at 6,400 MB/s and they are labeled as PC2-6400. And DDR3-1333 memories can transfer data at 10,664 MB/s and they are labeled as PC3-10600 or PC3-10666. As you can see, we use the number “2” or “3” after “DDR” or “PC” to indicate that we are talking about a DDR2 or DDR3 memory, not DDR.
The first classification, DDRxxx, is the standard used to classify memory chips, while the second classification, PCyyyy, is the standard used to classify memory modules. In Figure 1, you can see a PC3-10666 memory module, which uses DDR3-1333 memory chips. Pay attention to the RAM timings (7-7-7-18) and voltage (1.5 V).
KOMPUTERBAY 2GB (2 x 1GB) DDR DIMM (184 PIN) 400Mhz PC3200 CL 3.0 Desktop Memory
DUOMEIQI 8GB Kit（4X 2GB） 2RX8 DDR2 800MHz DIMM PC2-6300 PC2-6400 PC2-6400U CL6 1.8v 240 Pin Non-ECC Unbuffered Desktop Memory RAM Module Compatible with Intel AMD System
Patriot 16GB(2x8GB) Viper III DDR3 1600MHz (PC3 12800) CL9 Desktop Memory With Black Mamba Heatsink - PV316G160C9K
The maximum transfer rate for a memory module can be calculated through the following formula:
Maximum Theoretical Transfer Rate = clock x number of bits / 8
Since DIMM modules transfer 64 bits at a time, “number of bits” will be 64. As 64 / 8 equals 8, we can simplify this formula to:
Maximum Theoretical Transfer Rate = clock x 8
If the memory module is installed on a system where the memory bus is running at a lower clock rate, the maximum transfer rate the memory module will achieve will be lower than its theoretical maximum transfer rate. Actually, this is a very common misjudgment.
For example, let’s say that you bought a pair of DDR3-2133/PC3-17000 memories. Even though they are labeled as DDR3-2133, they won’t run at 2,133 MHz automatically on your system. This is the maximum clock rate they support, not the clock rate at which they will be running. If you install it on a regular PC system supporting DDR3 memories, they will probably run at 1,333 MHz (DDR3-1333) – which the maximum DDR3 standard speed –, achieving a maximum transfer rate of 10,664 MB/s (or 21,328 MB/s if they are running under dual channel mode, read our tutorial on dual channel to understand more about this subject). So, they won’t automatically run at 2,133 MHz nor automatically achieve the 17,000 MB/s transfer rate.
So, why would someone buy these modules? Someone would buy them for overclocking. Since the manufacturer guarantees that these modules will run up to 2,133 MHz, you know that you can raise the memory bus clock up to 1,066 MHz to achieve a higher performance with your system. However, your motherboard must support this kind of overclocking (read our tutorial on memory overclocking for more details). Thus buying a memory module with a labeled clock rate higher than what your system supports is useless if you are not going to overclock your system.
For the average user, that is everything you need to know about DDR, DDR2, and DDR3 memories. For the advanced user, there is yet another characteristic: the temporization of the memory, a.k.a. timings or latency. Let’s talk about it.
Because of timings, two memory modules with the same theoretical maximum transfer rate can achieve different performance levels. Why is this possible if both are running at the same clock rate?
Timings measure the time the memory chip delays doing something internally. Here is an example. Consider the most famous parameter, which is called CAS Latency (or CL or “access time”) that tells us how many clock cycles the memory module will delay in returning data requested by the CPU. A memory module with a CL 9 will delay nine clock cycles to deliver a requested data, whereas a memory module with a CL 7 will delay seven clock cycles to deliver it. While both modules may run at the same clock rate, the second one will be faster, as it will deliver data sooner than the first one. This issue is known as “latency.” As you can see in Figure 1, the module portrayed there has a CL of 7.
The memory timings are given through a series of numbers; for instance, 4-4-4-8, 5-5-5-15, 7-7-7-21, or 9-9-9-24. These numbers indicate the amount of clock cycles that it takes the memory to perform a certain operation. The smaller the number, the faster the memory. The memory module portrayed in Figure 1 has 7-7-7-18 timings, while the memory module portrayed in Figure 2 has 8-8-8-24 timings.
The operations that these numbers indicate are the following: CL-tRCD-tRP-tRAS-CMD. To understand them, bear in mind that the memory is internally organized as a matrix, where the data are stored at the intersection of the lines and columns.
Usually, you have two options: to configure your PC to use the memory standard timings, usually by setting memory configuration to “Auto” on the motherboard setup; or to manually configure your PC to use lower memory timings, which may increase the performance of your system. Notice that not all motherboards allow you to change the memory timings. Also, some motherboards may not be able to run at very low timings, and they may configure your memory module to run at a higher timing setting because of this.
When overclocking your memory, you may need to increase the memory timings in order to make the system run in a stable manner. Here is where something very interesting happens. Due to the increased timings, the memory may achieve a lower performance, even though it is now configured to run at a higher clock rate, due to the latency that was introduced.
That is another advantage of memory modules sold specifically for overclocking. The manufacturer, besides guaranteeing that your memory module will achieve the labeled clock rate, also guarantees that you will be able to keep the labeled timings up to the labeled clock.
For example, even though you may achieve 1,600 MHz (800 MHz x2) with DDR3-1333/PC3-10600 modules, on these modules it may be necessary to increase the memory timings, while on DDR3-1600/PC3-12800 ones the manufacturer guarantees that you will be able to achieve 1,600 MHz keeping the labeled timings.
Now we are going a step further as we will explain in detail each one of the memory timing parameters.
CAS Latency (CL) Impact on RAM Speed
As previously mentioned, CAS Latency (CL) is the best known memory parameter. It tells us how many clock cycles the memory will delay to return requested data. A memory with CL = 7 will delay seven clock cycles to deliver data, while a memory with CL = 9 will delay nine clock cycles to perform the same operation. Thus, for two memory modules running at the same clock rate, the one with the lowest CL will be faster.
Notice that the clock rate here is the real clock rate under which the memory module is running – i.e., half the rated clock rate. As DDR, DDR2, and DDR3 memories can deliver two data per clock cycle, they are rated with double their real clock rate.
In Figure 4, you can see how CL works. We gave two examples, a memory module with CL = 7 and a memory module with CL = 9. The command in blue would be a “read” command.
A memory with CL = 7 will provide a 22.2% improvement on memory latency over a memory with CL = 9, considering that both are running at the same clock rate.
You can even calculate the time the memory delays until it starts delivering data. The period of each clock cycle can be easily calculated through the formula:
T = 1 / f
Thus, the period of each clock cycle of a DDR3-1333 memory running at 1333 MHz (666.66 MHz clock) would be 1.5 ns (ns = nanosecond; 1 ns = 0.000000001 s). Keep in mind that you need to use the real clock rate, which is half of the labeled clock rate. So, this DDR3-1333 memory would delay 10.5 ns to start delivering data if it had CL =7, or 13.5 ns if it had CL = 9, for example.
SDRAM, DDR, DDR2, and DDR3 memories implement burst mode, where data stored in the next addresses can exit the memory at only one clock cycle. So, while the first data would delay CL clock cycles to exit the memory, the next data would be delivered right after the prior data that has just come out from the memory, not having to wait for another CL cycle. Also, DDR, DDR2, and DDR3 memories deliver two data per clock cycle, and that is why they are labeled as having twice their real clock rate.
RAS to CAS Delay (tRCD) Impact on RAM Speed
Each memory chip is organized internally as a matrix. At the intersection of each row and column we have a small capacitor that is in charge of storing a “0” or a “1” – the data. Inside the memory, the process of accessing the stored data is accomplished by first activating the row then the column where it is located. This activation is done by two control signals called RAS (Row Address Strobe) and CAS (Column Address Strobe). The less time there is between these two signals the better, as the data will be read sooner. RAS to CAS Delay or tRCD measures this time. In Figure 5 we illustrate this, showing a memory with tRCD = 3.
As you can see, RAS to CAS Delay is also the number of clock cycles taken between the “Active” command and a “read” or “write” command.
As with CAS Latency, RAS to CAS Delay works with the memory real clock (which is half of the labeled clock). The lower this parameter, the faster the memory will be, as it will start reading or writing data earlier.
RAS Precharged (tRP) Impact on RAM Speed
After data is gathered from the memory, a command called Precharge needs to be issued, closing the memory row that was being used and allowing a new row to be activated. RAS Precharge time (tRP) is the time taken between when the Precharge command and the next Active command can be issued. As we learned from the previous page, the Active command starts a read or write cycle.
In Figure 6, we are giving an example of a memory with tRP = 3.
As with the other parameters, RAS Precharge works with the memory real clock (which is half of the labeled clock). The lower this parameter, the faster the memory will be, as it will issue the Active command earlier.
Adding everything we’ve seen, the time elapsed between issuing the Precharge command and actually getting the data will be tRP + tRCD + CL.
Other Parameters Impacting RAM Timings
Let’s take a better look at the other two parameters, Active to Precharge Delay (tRAS) and Command Rate (CMD). As with the other parameters, these two parameters work with the memory real clock (which is half of the memory labeled clock). The lower these parameters, the faster the memory will be.