Arctic Cooling NV Silencer 6 (Rev. 2) VGA Cooler
By Gabriel Torres on June 3, 2006


Introduction

Arctic Cooling manufactures a series of VGA coolers that are very silent and pull the hot air generated by the video card to outside the computer case. At least two VGA manufacturers – HIS and Sapphire – sell their VGAs using VGA coolers from Arctic Cooling. If you don’t have a VGA using an exotic cooling system, you can buy a VGA cooler from Arctic Cooling and install it yourself. We’ve got a NV Silencer 6 (Rev. 2) sample, which is targeted to GeForce FX 5700, GeForce 6200 and GeForce 6600 series. Let’s take a look at it.

You can see the full list of VGA coolers from Arctic Cooling on their website. As you can see there, they have several different models, each one targeted to specific video cards. There are several reasons you cannot use a VGA cooler targeted to one video card on another. First, the holes located on the video card used to fasten the cooler to it may differ in position. The second reason is that each graphics chip has different thermal requirements – i.e., the minimum size and material of the cooler base and fins vary according to the graphics chip. Third, the VGA cooler may be bigger than the space available on the video card (for example, the area surrounding the graphics chip may have other components like electrolytic capacitors that prevent the installation of bigger coolers).

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 1: NV Silencer 6 (Rev. 2) in its package.

In Figure 2, you can see everything that comes with the product, including a tube of thermal grease.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 2: Items that come with NV Silencer 6 (Rev. 2).

NV Silencer 6 (Rev. 2) VGA cooler has a big 72 mm fan rotating at a relatively low speed (1,500 rpm) in order to achieve a low noise level. This fan pulls air from inside the PC case, makes it to pass through the cooler fins and going outside the computer case through a duct.

The heatsink base is made of copper, while the heatsink fins are made of aluminum, as you can see on Figures 3 and 4.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 3: The heatsink base is made of copper.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 4: The heatsink fins are made of aluminum.

In Figure 5 you have a comparison between NV Silencer 6 (Rev. 2) and the coolers that come with video cards from Sapphire and HIS. This particular Sapphire model is using an ATI Silencer 5 (Rev. 2), while this particular HIS model is using a VGA silencer Rev. 3, both are manufactured by Arctic Cooling.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 5: NV Silencer 6 (Rev. 2), a Sapphire Radeon X800 Pro and a HIS Radeon X1600 Pro.

Installation

NV Silencer 6 (Rev. 2) installation is very simple and even a layperson can replace the original cooler from his/her video card and replace it with this VGA cooler from Arctic Cooling. We are going to show you how to do it on a GeForce 6600 GT.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 6: We are going to replace the original cooler from our GeForce 6600 GT with Arctic Cooling’s.

The first step is to remove the original cooler from your video card. On our GeForce 6600 GT this was accomplished by pushing two plastic pegs located on the backside of the card. After removing the cooler you need to unplug the fan power cable from the card.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 7: GeForce 6600 GT with its original cooler removed.

After removing the original cooler, you will need to remove all thermal grease that may exist on the graphics chip using a dry cloth. Then you need to apply a small amount of the thermal grease that comes with the product on the center of the graphics chip. Here you need to be very careful to not put too much thermal grease. We show the correct amount in Figure 9. Don’t worry that the thermal grease isn’t covering the whole surface of the graphics chip: when we install the cooler the thermal grease will fill the spots that were left over.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 8: Applying thermal grease.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 9: The correct amount of thermal grease that should be applied.

Installation (Cont’d)

Now you need to install the fan power cable.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 10: Installing the fan power cable.

You need to study where this cable will be located after the cooler is in its final position before installing it. In our case, the cable would be located below the plastic duct, in front of the heatsink fins, which we though was no good, as it would be blocking the airflow. So we needed to release the cable a little bit and make it to go over the plastic duct (see Figure 14).

Put the VGA cooler in place, inserting the two screws available in the holes located on the board and then turn the video card over. You will find the two screws as shown in Figure 11.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 11: VGA cooler screws.

Place the rubber pad and the metallic clip as shown in Figure 12.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 12: Installing the rubber pad and the metallic clip.

Screw the two nuts to the screws, as shown in Figure 13.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 13: Screw the two nuts to the screws.

That’s it. Your NV Silencer 6 (Rev. 2) is now installed as you can see in Figure 14. Pay attention to the fan power cable location. As mentioned, we had to pass it over the plastic duct in order to not mess with the airflow.

Arctic Cooling NV Silencer 6 (Rev. 2)
click to enlarge
Figure 14: NV Silencer 6 (Rev. 2) installed.

Main Specifications

Arctic Cooling NV Silencer 6 (Rev. 2) VGA cooler main features include:

Conclusions

This is a great product. After installing our GeForce 6600 GT back to our PC we couldn’t even hear the fan working. Really amazing. Even working at a relatively low rotation, this fan produces a very strong airflow. Arctic Cooling also gives a 6-year warranty to their VGA coolers, which is really impressive.

We think this product is good for both the enthusiast and the regular user. It will probably bring a better VGA overclocking experience for the enthusiast and, at the same time, will prevent your PC from overheating, as it removes hot air from your computer. Put this together with its very low noise level and you have a great product.

What is also really great is that even though we took a look at the model targeted to GeForce FX 5700, GeForce 6200 and GeForce 6600 series, Arctic Cooling provides versions of this product to a myriad of video cards, covering virtually all video cards available on the market.

The only problem we see on this product is its price. We think its suggested price (USD 29.00) is a little bit high for this product – even though it is a high quality and above the average product – and what is even more problematic is that this product can be found costing even more (it is being quoted at USD 35 at Tigerdirect.com). So you need to pay close attention to not be overcharged.

Originally at http://www.hardwaresecrets.com/article/Arctic-Cooling-NV-Silencer-6-Rev-2-VGA-Cooler/336


© 2004-14, Hardware Secrets, LLC. All Rights Reserved.

Total or partial reproduction of the contents of this site, as well as that of the texts available for downloading, be this in the electronic media, in print, or any other form of distribution, is expressly forbidden. Those who do not comply with these copyright laws will be indicted and punished according to the International Copyrights Law.

We do not take responsibility for material damage of any kind caused by the use of information contained in Hardware Secrets.