Lian Li Tyr PC-X500 Case Review

Inside Tyr PC-X500

Opening Tyr PC-X500 is very easy, all you have to do is unscrew the thumbscrew and pull the mechanism where the screw is attached to. The thumbscrews remain attached to these mechanisms, so there is no chance of losing the screws. Even though you can remove both panels the motherboard tray is permanently attached to the chassis. Both side panels have a thin foam sheet attached in order to absorb noise.

click to enlarge
Figure 9: Side panels have a thin foam sheet attached.

click to enlarge
Figure 10: Inside Tyr PC-X500.

As you know, this case uses a unique design. Internally the case is divided in three separated compartments, which improves airflow and thus one should expect a computer built using this case to run cooler than PCs based on traditional cases.

On the lower section we have the motherboard compartment. This compartment is cooled by three 120-mm fans, two on the front and one on the rear. All fans used on this case use a three-pin connector for motherboards, so you can install them on your motherboard to monitor their speed thru your favorite monitoring program (if you want them to rotate at their full speed all the time) or to the small speed controller available. The fans come with adaptors installed for you to connect them to the traditional peripheral power connectors from the power supply.

Then we have the power supply compartment (see how the power supply is attached to the case using thumbscrews that remain attached to the case on Figure 11), where you can also find one of the two hard disk drive cages – each cage can hold up to two hard disk drives – and the external 3 ½” bay. If you don’t have a floppy disk drive this bay can be used to hold a fifth hard disk drive.

And the third compartment is located on the top of the case and is cooled by a fourth 120-mm fan. On this compartment we have the second hard disk drive cage and the two 5 ¼” bays.

click to enlarge
Figure 11: Detail of the top two compartments.

On Figure 12 you can see the rear side of the motherboard compartment with its rear 120-mm fan. This case doesn’t use a screwless mechanism to fasten daughter boards to the case, but on the other hand it provides thumbscrews, allowing fastening cards without the need of using tools anyway. In fact we personally prefer this approach, as we’ve seen countless times these screwless mechanisms breaking because they are usually manufactured using cheap plastic.

click to enlarge
Figure 12: Rear 120-mm fan and thumbscrews for fastening daughter boards.

On Figure 13 you can have a better look on the two front 120-mm fans.

click to enlarge
Figure 13: Front 120-mm fans.

Lian Li Tyr PC-X500 Case Review
By Gabriel Torres on July 11, 2008	Page 3 of 6
Inside Tyr PC-X500 Opening Tyr PC-X500 is very easy, all you have to do is unscrew the thumbscrew and pull the mechanism where the screw is attached to. The thumbscrews remain attached to these mechanisms, so there is no chance of losing the screws. Even though you can remove both panels the motherboard tray is permanently attached to the chassis. Both side panels have a thin foam sheet attached in order to absorb noise. click to enlarge Figure 9: Side panels have a thin foam sheet attached. click to enlarge Figure 10: Inside Tyr PC-X500. As you know, this case uses a unique design. Internally the case is divided in three separated compartments, which improves airflow and thus one should expect a computer built using this case to run cooler than PCs based on traditional cases. On the lower section we have the motherboard compartment. This compartment is cooled by three 120-mm fans, two on the front and one on the rear. All fans used on this case use a three-pin connector for motherboards, so you can install them on your motherboard to monitor their speed thru your favorite monitoring program (if you want them to rotate at their full speed all the time) or to the small speed controller available. The fans come with adaptors installed for you to connect them to the traditional peripheral power connectors from the power supply. Then we have the power supply compartment (see how the power supply is attached to the case using thumbscrews that remain attached to the case on Figure 11), where you can also find one of the two hard disk drive cages – each cage can hold up to two hard disk drives – and the external 3 ½” bay. If you don’t have a floppy disk drive this bay can be used to hold a fifth hard disk drive. And the third compartment is located on the top of the case and is cooled by a fourth 120-mm fan. On this compartment we have the second hard disk drive cage and the two 5 ¼” bays. click to enlarge Figure 11: Detail of the top two compartments. On Figure 12 you can see the rear side of the motherboard compartment with its rear 120-mm fan. This case doesn’t use a screwless mechanism to fasten daughter boards to the case, but on the other hand it provides thumbscrews, allowing fastening cards without the need of using tools anyway. In fact we personally prefer this approach, as we’ve seen countless times these screwless mechanisms breaking because they are usually manufactured using cheap plastic. click to enlarge Figure 12: Rear 120-mm fan and thumbscrews for fastening daughter boards. On Figure 13 you can have a better look on the two front 120-mm fans. click to enlarge Figure 13: Front 120-mm fans.
Originally at http://www.hardwaresecrets.com/article/582/3	Pages (6): 1 2 3 4 5 6 »
© 2004-9, Hardware Secrets, LLC. All Rights Reserved. Total or partial reproduction of the contents of this site, as well as that of the texts available for downloading, be this in the electronic media, in print, or any other form of distribution, is expressly forbidden. Those who do not comply with these copyright laws will be indicted and punished according to the International Copyrights Law. We do not take responsibility for material damage of any kind caused by the use of information contained in Hardware Secrets.