Load Tests

We made several tests with this power supply as described in the article Hardware Secrets Power Supply Test Methodology.

We tested this power supply under five different loads patterns, trying to pull around 20%, 40%, 60%, 80% and 100% of its maximum capacity (under “% Max Load” we list the actual percentage that was used), watching how the reviewed unit behaved under each load.

If you add all the powers listed for each test you may find a value different from what posted under “Total” below. Since each output can have a slight variation (e.g. +5 V output working at 5.10 V) the actual total amount of power being delivered is slightly different from the calculated value. On “Total” row we are using the real amount of power being delivered, as measured by our load tester.

+12V2 is the second +12V input from our load tester and during our tests it was connected to the power supply EPS12V connector, which is the only thing connected to the unit’s +12V1 rail. +12V1 is the first +12V input from our load tester and we connected the video card auxiliary power cable, the peripheral power cables and the main motherboard cable to it, so it was connected to +12V3 and +12V4 rails from the power supply.

We tried to use the same load pattern we used to test other 600 W units for a better comparison of the achieved results. We, however, had to use a different configuration for the test number 5 (100% load) because the power supply wouldn’t turn on if we configured the +12V2 input from our load tester (which was in fact connected to the power supply +12V1 rail) to pull 21.5 A like we did with other units. Since on the label was saying that each rail had a 16 A limit, this means that over current protection (OCP) was kicking in – which is great, by the way. So we had to reduce the current on +12V2 input and increase it on +12V1, which lead to a different configuration compared to tests we’ve done with other units on the 600 W range.

This power supply can really deliver 600 W of power at a room temperature of almost 49º C, which is great.

The highlight of Zalman ZM600-HP is clearly efficiency. When we pulled up to 80% of the maximum labeled capacity (489 W) we could see efficiency of at least 86%, peaking almost 89% when we pulled 40% of the maximum labeled capacity (247 W). When we pulled 100% of the labeled power, this unit was still delivering efficiency above 80%, of practically 84%, which is outstanding.

Voltage stability was another highlight of this product, with all outputs between 3% of their nominal voltage in all tests, which is excellent (ATX standard allows voltages to be up to 5% from their nominal values and 10% in the case of the -12 V output). So voltages were always very close to their nominal values.

Noise level was also outstanding, far below the maximum allowed (120 mV peak-to-peak for 12 V outputs and 50 mV peak-to-peak for +5 V and +3.3 V outputs). Below you can see noise level for the test number five, when we were pulling 600 W from this unit.

click to enlarge
Figure 21: Noise level at +12V1 with power supply delivering 600 W (38.8 mV).

click to enlarge
Figure 22: Noise level at +12V2 with power supply delivering 600 W (51 mV).

click to enlarge
Figure 23: Noise level at +5 V with power supply delivering 600 W (26.4 mV).

click to enlarge
Figure 24: Noise level at +3.3 V with power supply delivering 600 W (26.8 mV).

Let’s now see if we could pull even more power from this unit and our tests of the power supply protections.

Total or partial reproduction of the contents of this site, as well as that of the texts available for downloading, be this in the electronic media, in print, or any other form of distribution, is expressly forbidden. Those who do not comply with these copyright laws will be indicted and punished according to the International Copyrights Law.

We do not take responsibility for material damage of any kind caused by the use of information contained in Hardware Secrets.