How Analog-to-Digital Converter (ADC) Works

Parallel Design

The Flash ADC, also called parallel ADC, is very easy to understand. It works by comparing the input voltage – i.e. the analog signal – to a reference voltage, which would be the maximum value achieved by the analog signal. For example, if the reference voltage is of 5 volts, this means that the peak of the analog signal would be 5 volts. On an 8-bit ADC when the input signal reached 5 volts we would find a 255 (11111111) value on the ADC output, i.e. the maximum value possible.

Then the voltage reference is lowered thru a resistor network and other comparators added, so the input voltage (analog signal) can be compared to other values.

On Figure 6 you can see a 3-bit Flash ADC. The comparison is done thru an op amp. All resistors have the same value.

click to enlarge
Figure 6: Flash ADC.

The priority encoder can be done using XOR gates and a series of diodes and resistors, like shown on Figure 7, or a single chip like 74148 (3-line to 8-line priority encoder).

click to enlarge
Figure 7: Flash ADC.

Even though Flash ADC uses a very simple design, it requires a lot of components. The number of required comparers is 2^n-1, where n is the number of output bits. Thus for an eight-bit Flash ADC 255 comparers would be necessary, and for a 16-bit Flash ADC, 65,535!

On the other hand, Flash ADC is the fastest ADC type available. The digital equivalent of the analog signal will be available right away at it output (it will only have the propagation delay inserted by the logic gates) – hence the name “flash”.

Another advantage of Flash ADC is that you can create an ADC with non-linear output. Usually ADCs have a linear output, i.e. each digital number corresponds to a fixed voltage increase on the analog input. For example, on the 3-bit ADC shown above with a Vref of 5 V, each digital number would represent 625 mV (5 V / 2^3). So 0 V = 000, 0.625 V = 001, 1.250 V = 010 and so on up to 5 V = 111.

Since Flash ADC comparisons are set by a set of resistors, one could set different values for the resistors in order to obtain a non-linear output, i.e. one value would represent a different voltage step from the other values.

How Analog-to-Digital Converter (ADC) Works
By Gabriel Torres on April 21, 2006	Page 6 of 10
Parallel Design The Flash ADC, also called parallel ADC, is very easy to understand. It works by comparing the input voltage – i.e. the analog signal – to a reference voltage, which would be the maximum value achieved by the analog signal. For example, if the reference voltage is of 5 volts, this means that the peak of the analog signal would be 5 volts. On an 8-bit ADC when the input signal reached 5 volts we would find a 255 (11111111) value on the ADC output, i.e. the maximum value possible. Then the voltage reference is lowered thru a resistor network and other comparators added, so the input voltage (analog signal) can be compared to other values. On Figure 6 you can see a 3-bit Flash ADC. The comparison is done thru an op amp. All resistors have the same value. click to enlarge Figure 6: Flash ADC. The priority encoder can be done using XOR gates and a series of diodes and resistors, like shown on Figure 7, or a single chip like 74148 (3-line to 8-line priority encoder). click to enlarge Figure 7: Flash ADC. Even though Flash ADC uses a very simple design, it requires a lot of components. The number of required comparers is 2^n-1, where n is the number of output bits. Thus for an eight-bit Flash ADC 255 comparers would be necessary, and for a 16-bit Flash ADC, 65,535! On the other hand, Flash ADC is the fastest ADC type available. The digital equivalent of the analog signal will be available right away at it output (it will only have the propagation delay inserted by the logic gates) – hence the name “flash”. Another advantage of Flash ADC is that you can create an ADC with non-linear output. Usually ADCs have a linear output, i.e. each digital number corresponds to a fixed voltage increase on the analog input. For example, on the 3-bit ADC shown above with a Vref of 5 V, each digital number would represent 625 mV (5 V / 2^3). So 0 V = 000, 0.625 V = 001, 1.250 V = 010 and so on up to 5 V = 111. Since Flash ADC comparisons are set by a set of resistors, one could set different values for the resistors in order to obtain a non-linear output, i.e. one value would represent a different voltage step from the other values.
Originally at http://www.hardwaresecrets.com/article/317/6	Pages (10): 1 2 3 4 5 6 7 8 » ... Last »
© 2004-9, Hardware Secrets, LLC. All Rights Reserved. Total or partial reproduction of the contents of this site, as well as that of the texts available for downloading, be this in the electronic media, in print, or any other form of distribution, is expressly forbidden. Those who do not comply with these copyright laws will be indicted and punished according to the International Copyrights Law. We do not take responsibility for material damage of any kind caused by the use of information contained in Hardware Secrets.