Form Factors

There are several different form factors (or “standards”) for PC power supplies. These form factors define not only the physical size of the power supply, but also the kind of connectors the power supply has. As this writing ATX12V 2.x and EPS12V are the most common standards for PC power supplies.

• AT: This standard was introduced by the IBM PC AT in 1984 and was used until the ATX standard gained popularity in mid-1990’s. This power supply delivers four voltages, +5 V, +12 V, -5 V and -12 V, and the main motherboard connector uses a 12-pin connector (see previous page). From the connectors presented this kind of power supply uses only the standard peripheral power connectors and the floppy disk drive power connector, besides the 12-pin motherboard cable, of course.
• ATX: In 1996 Intel introduced a new motherboard layout called ATX to replace the old AT layout. Because the ATX motherboard had completely different physical dimensions, new cases were also needed (“ATX cases”, contrasted to the “AT cases” used so far). With this new motherboard layout Intel also proposed a new kind of power supply, providing new features, like the use of a new 20-pin motherboard connector and the introduction of two new voltages, +3.3 V and +5VSB, also known as “standby power”. This output is always turned on even when the computer is turned off, which allowed the computer to turn itself off without requiring you to press an on/off switch. From the connectors presented, this kind of power supply uses only a 20-pin motherboard connector, the standard peripheral power connectors and the floppy disk drive power connector. You can find the complete ATX specification here.
• ATX12V 1.x: With modern CPUs requiring more power, two extra connectors were added to ATX power supplies: a four-pin 12 V connector (ATX12V connector) and a six-pin auxiliary power (see previous page). ATX12V 1.3 introduced the Serial ATA power connector. You can find the complete ATX12V 1.x specification here.
• ATX12V 2.x: This form factor was introduced with the release of the PCI Express bus and upgraded the main motherboard power connector to a 24-pin model (Figures 6 and 7) and introduced the PCI Express auxiliary power connector (PEG, Figures 13 and 14). You can find the complete ATX12V 2.x specification here. This is the standard used nowadays.
• EPS12V: This form factor was created by SSI (Server System Infrastructure) for entry-level servers. Its current version uses the same plugs from ATX12V 2.x adding a new CPU power plug, called EPS12V (see Figures 10, 11 and 12). Since it brings only one new connector, many power supply manufacturers provide models that are ATX12V v2.x and EPS12V at the same time. You can find the complete EPS12V specification here.

So far we took a look on the main power supply form factors for desktop PCs. There are, however, other form factors available for small form factor PCs.

• LFX12V: LFX stands for Low Profile Form Factor. It uses the same connectors as ATX12V v2.x but has a different physical size: 2.44” x 2.83” x 8.27” (62 mm x 72 mm x 210 mm) (W x H x D).

click to enlarge
Figure 23: LFX12V power supply.

• CFX12V: CFX stands for Compact Form Factor. It uses the same connectors as ATX12V v2.x and is “L” shaped based on the standard ATX size, with a 5.90” (150 mm) width at its top and 4” (101.6 mm) width at its bottom. You can find the complete CFX12V specification here.
• TFX12V: TFX stands for Thin Form Factor. It uses the same connectors as ATX12V v2.x but has a different physical size: 2.56” x 3.35” x 6.89” (65 mm x 85 mm x 175 mm) (W x H x D). You can find the complete CFX12V specification here.
• SFX12V: SFX stands for Small Form Factor. You can find the complete SFX12V specification here. It uses the same connectors as ATX12V v2.x and can be found in several different physical sizes and fan configurations:
• 3.94” x 1.97” x 4.92” (100 mm x 50 mm x 125 mm) (W x H x D) (a.k.a. 40mm Fan Profile)
• 3.94” x 2.5” x 4.92” (100 mm x 63.5 mm x 125 mm) (W x H x D) (a.k.a. Top Mount Fan Profile)
• 4.92” x 2.5” x 3.94” (125 mm x 63.5 mm x 100 mm) (W x H x D) (a.k.a. Reduced Depth Top Mount Fan Profile)
• 3.94” x 2.5” x 4.92” (100 mm x 63.5 mm x 125 mm) (W x H x D) (a.k.a. 60mm Fan Profile)
• 5.43” x 3.38” x 3.99” (138 mm x 86 mm x 101.4 mm) (W x H x D) (a.k.a. PS3 Profile)

Total or partial reproduction of the contents of this site, as well as that of the texts available for downloading, be this in the electronic media, in print, or any other form of distribution, is expressly forbidden. Those who do not comply with these copyright laws will be indicted and punished according to the International Copyrights Law.

We do not take responsibility for material damage of any kind caused by the use of information contained in Hardware Secrets.