Hardware Secrets

Home | Camera | Case | CE | Cooling | CPU | Input | Memory | Mobile | Motherboard | Networking | Power | Storage | Video | Other
Content
Articles
Editorial
First Look
Gabriel’s Blog
News
Reviews
Tutorials
Main Menu
About Us
Awarded Products
Datasheets
Dictionary
Download
Drivers
Facebook
Forums
Links
Manufacturer Finder
Newsletter
On The Web
RSS Feed
Test Your Skills
Twitter
Newsletter
Subscribe today!
Search
Recommended
Troubleshooting and Repairing Computer Printers
Troubleshooting and Repairing Computer Printers, by Stephen Bigelow (McGraw-Hill/TAB Electronics), starting at $9.98



Home » Other » Printer
How to Unclog Epson Print Heads
Author: Gabriel Torres and Alexandre Souza
Type: Tutorials Last Updated: August 6, 2005
Page: 4 of 4
Unclogging the Print Head

With the print head in your hands, take out the print cartridges and clean them with alcohol to remove the ink that accumulated on the surface. Also, use this opportunity to check how things work or fix any problem on the carriage assembly. After the cleaning, let’s move to the complicated part.

First you will need to make your own Epson print head unclogger. Get a 10 cc or 20 cc injection syringe with no needle. Then, go to the nearest model aeronautics store and ask for a 1-inch piece of model aircraft fuel hose. For those who don’t know, it’s a hose made of silicone, extremely flexible. You’ll cut a piece of around ½ inch and put it at the end of the syringe. That’s it! You’ve made your own Epson print head unclogger.

Now, let’s do the work.

Imagine print heads as a funnel. If you push down (narrow part) to up (large part), it’s easier than if you push from up (large part) to down (narrow part). First you will try to inject isopropylic alcohol (isopropanol) from up to down (regular alcohol is not recommended for containing water, that can damage the mechanism). You will fill the syringe up with alcohol, connect the hose that you fixed to the end of the syringe in the tube that goes inside the print cartridge, and force the alcohol out through the ink way. If you look under, you’ll see that there are several small holes that should all be unclogged. Check that out by injecting alcohol from above: there should be alcohol passing through all the holes, not missing a single one. Do that with all heads of the set (your printer can have two or four heads, depending on the model).

In case any hole is clogged, don’t try to inject alcohol from below, but try to PULL the alcohol from below. There lies the main use of that model airplane fuel hose. It’s so flexible (silicone) that the hose forms an excellent sealing around it, so the suction made by the syringe is so powerful that pulls out any clogging that may be on the head. Notice that TRYING TO PUSH UP WILL NOT WORK. The end of the funnel is facing down (facing the paper) and if you try to push the alcohol from down to up, you’ll clog the head even more. The thing is, SUCK the dirt under the head. Notice that it’s A LOT easier if you have, or make, a vacuum pump, but we use what’s at our hand…

Repeat the procedure until you are sure that ALL holes are unclogged. If you leave one single hole clogged, you’ll have to do the work all over again. And it’s painful. It’s a 2-3 hours activity and it’s a procedure that has to be done with all patience and calm.

After you have unclogged all the holes, calmly reassemble the printer, paying attention to the position of the timing belt and of the parallelism adjustment bushings. They have to be in the same place they were before.

After the printer is reassembled, put two NEW and ORIGINAL cartridges in place and perform the printer test for about 10 (yes, I said TEN) times, to be absolutely sure that all jets are working. If all jets are working, you can stamp the seal ”OK“ and charge your client a fair value. After all, a single color ink jet is very expensive!

Another important detail: every technician that repairs printers must know the qualities and limitations of each printer, and has to tell the clients to use best quality supply, original or not. Alternative supply may be cheaper, but I rarely see an Epson printer getting clogged with original ink. It works this way since dot matrix printers: the head lasted much longer if only original tapes were used – and they had INCREDIBLY better quality. But this is another issue…

« Previous |  Page 4 of 4
Print Version | Send to Friend | Bookmark Article | Comments (2)

Related Content
  • How to Refill Epson Cartridges
  • How to Manually Clean Your VCR Heads
  • Lexmark HQ Tour in Lexington, Kentucky, USA
  • Epson WorkForce 610 All-in-One Printer Review
  • Epson B-510DN Ink Jet Printer Review


  • RSSLatest News
    LUXA2 Releases New P1-PRO Battery Power Pack
    October 1, 2013 - 7:23 AM PST
    MSI unveils GP70 and GP60 Laptops
    September 30, 2013 - 7:23 AM PST
    AMD Unveils Next-Generation Radeon Graphics Cards
    September 27, 2013 - 5:33 AM PST
    Genius Introduces Energy Mouse in North America
    September 27, 2013 - 5:32 AM PST
    Apple Updates iMac
    September 25, 2013 - 5:27 AM PST
    .:: More News ::.







    © 2004-13, Hardware Secrets, LLC. All rights reserved.
    Advertising | Legal Information | Privacy Policy
    All times are Pacific Standard Time (PST, GMT -08:00)