|Everything You Need to Know About the CPU C-States Power Saving Modes|
In order to save energy when the CPU is idle, the CPU can be commanded to enter a low-power mode. Each CPU has several power modes and they are collectively called “C-states” or “C-modes.” In this tutorial we will explain what these modes are, what they do and the modes supported by each processor.
The lower-power mode was first introduced with the 486DX4 processor, so this concept is far from being new. With time, however, more power modes were introduced and enhancements were made to each mode so the CPU could consume less power when it is one of these low-power modes.
The basic idea of these modes is to cut the clock signal and power from idle units inside the CPU. The more units you stop (by cutting the clock), reduce the voltage or even completely shut down, more energy you save, but more time is required for the CPU to “wake up” and be again 100% operational.
These modes are known as “C-states.” They are numbered starting at C0, which is the normal CPU operating mode, i.e., the CPU is 100% turned on. The higher the C number is, deeper is the CPU sleep mode, i.e., more circuits and signals are turned off and more time the CPU will take to go back to C0 mode, i.e., to wake-up.
Each mode is also known by a name and several of them have sub-modes with different power saving – and thus wake-up time – levels.
In the table below we summarize all C-state modes currently available. Modes C1 to C3 work by basically cutting clock signals used inside the CPU, while modes C4 to C6 work by reducing the CPU voltage. “Enhanced” modes can do both at the same time.
What it does
CPU fully turned on
Stops CPU main internal clocks via software; bus interface unit and APIC are kept running at full speed.
486DX4 and above
Stops CPU main internal clocks via software and reduces CPU voltage; bus interface unit and APIC are kept running at full speed.
All socket LGA775 CPUs
Stops all CPU internal clocks.
Turion 64, 65-nm Athlon X2 and Phenom CPUs
Stops CPU main internal clocks via hardware; bus interface unit and APIC are kept running at full speed.
486DX4 and above
Stops CPU internal and external clocks via hardware
Only 486DX4, Pentium, Pentium MMX, K5, K6, K6-2, K6-III
Extended Stop Grant
Stops CPU main internal clocks via hardware and reduces CPU voltage; bus interface unit and APIC are kept running at full speed.
Core 2 Duo and above (Intel only)
Stops all CPU internal clocks
Pentium II, Athlon and above, but not on Core 2 Duo E4000 and E6000
Stops all CPU internal and external clocks
Pentium II and above, but not on Core 2 Duo E4000 and E6000; Turion 64
Stops all CPU internal clocks and reduces CPU voltage
AMD Turion 64
Reduces CPU voltage
Pentium M and above, but not on Core 2 Duo E4000 and E6000 series; AMD Turion 64
Enhanced Deeper Sleep
Reduces CPU voltage even more and turns off the memory cache
Core Solo, Core Duo and 45-nm mobile Core 2 Duo only
Deep Power Down
Reduces the CPU internal voltage to any value, including 0 V
45-nm mobile Core 2 Duo only
Now we are going to explain each C-state in details.
| Page 1 of 6 | Next » |
|Print Version | Send to Friend |
| Comments (0)
October 1, 2013 - 7:23 AM PST
September 30, 2013 - 7:23 AM PST
September 30, 2013 - 7:22 AM PST
September 27, 2013 - 5:33 AM PST
September 27, 2013 - 5:32 AM PST
September 27, 2013 - 5:30 AM PST
September 26, 2013 - 6:30 AM PST
September 26, 2013 - 6:21 AM PST
September 26, 2013 - 6:15 AM PST
September 25, 2013 - 5:27 AM PST
Our Most Popular Articles
Latest Threads in Our Forums
by Gabriel Torres
by Hardware Secrets Team
by Gabriel Torres